category：Building materials / date：2022-07-01 02:09:06 / browse：134 / comment：6
The selection of pipes and fittings for welding data preparation shall be based on the quality elements of the application environment, chemical composition and application pressure, and the improvement of corrosion resistance of stainless steel materials by simple chemical passivation is limited. On the other hand, the traditional passivation treatment containing chromium salt has been gradually eliminated, and the passivation treatment of stainless steel has turned to the direction of environmental friendliness. Recently, citric acid passivation and silicon treatment on stainless steel surface have become a new research direction. The former has environmental protection characteristics because its passivation solution component does not contain chromium salt. The latter has found that silicon coupling agent is chemically adsorbed on the metal surface to form a protective silicon film with cross-linked network structure. The length of discoloration time of samples after different surface treatments was compared by blue dot method, the corrosion rate of samples after different surface treatments was distinguished by brine immersion test, and the salt spray resistance of samples after different surface treatments was distinguished by neutral salt spray test, The differences of pitting corrosion resistance and resistance to corrosive medium of samples after different surface treatment were compared by electrochemical test. The film thickness of silicon film was indirectly characterized by film weight test, and scanning electron microscope, energy spectrometer, X-ray diffraction X-ray photoelectron spectroscopy and total reflection Fourier transform infrared spectroscopy characterized the surface films of different surface treated samples, and analyzed the structural composition and corrosion resistance mechanism of different films. Professional stainless steel plate, stainless steel coil, stainless steel belt, stainless steel pipe, high price, service, on-site settlement, honest management! At present, there are few studies on the combination of citric acid passivation and silicon treatment of stainless steel. Therefore, and discusses the corrosion resistance mechanism of different films on its surface silicon treatment and the combination of citric acid passivation and acid silicon system treatment which can provide reference for the new direction of stainless steel surface treatment, It has certain practical guiding significance. The corrosion resistance and mechanism of chemical passivation, silicon treatment and composite treatment of martensitic stainless steel were studied in this paper. The comprehensive comparison of the research results shows that the corrosion resistance of stainless steel treated with different surface treatments is different. The corrosion resistance of the sample treated with silicon alone is better than that treated with traditional dichromate passivation. The corrosion resistance of the composite treated sample treated with citric acid passivation and acid silicon system is further enhanced than that treated with acid silicon system alone. The composite treatment of citric acid passivation and acid silicon system treatment has excellent corrosion resistance and environmental protection characteristics, and is expected to replace the traditional dichromate passivation treatment. According to the film weight test results, the surface silicon film weight of the composite treated sample after citric acid passivation and acid silicon system treatment is lower than that of the sample after acid silicon system treatment alone, indicating that the excellent corrosion resistance of the composite film not only depends on the surface silicon film, but also benefits from its double-layer film structure.Patarra,SPCC stainless steel belt is simply an extension of ultra-thin stainless steel plate. It is mainly a narrow and long steel plate produced to meet the needs of industrialized production of various metal or mechanical products in different industrial sectors.Marking: in order to make the steel pipe complete the socket of the pipe fitting, the length must be marked and marked at the pipe end.Kumasi,The bright nickel layer on the stainless steel pipe is a silver white metal with slight yellow light. Its hardness is higher than that of copper, zinc tin, cadmium, but lower than that of chromium and rhodium. Bright nickel has high chemical stability in air and good stability to alkali. Using Brightener on stainless steel pipe, bright nickel can be directly plated without polishing, so as to improve the hardness, wear resistance and leveling of the surface, make the appearance of stainless steel pipe consistent with other nickel plated parts, and avoid the corrosion of potential difference between stainless steel pipe and other bright nickel. After using bright nickel solution for a period of time,PatarraStainless steel bright annealed tube, due to the of brightenerFormula for hydraulic test pressure of stainless steel welded pipe for weight calculation fluid (gbt-): where: P - test pressure, MPa; R - stress, taking yield point of %, MPa; s - nominal wall thickness of steel pipe, mm.Stainless steel seamless steel pipe for fluid transportation (instead of gbt- instead of gbt- instead of gb-)
Low temperature embrittlement of stainless steel pipe --- in low temperature environment, the deformation energy is small. In low temperature environment, Guangdong Province in the tenth generation of the last century. With the rapid development of science and technology in recent decades, stainless steel pipe production is all over the country. Stainless steel pipe is more and more widely used. But in fact, most people, including many people in the industry, do not know much about the classification and application of stainless steel pipes. Take stainless steel pipe for example.Stainless steel pipe packing bag is nothing more than the function of protecting the surface of stainless steel pipe, so most stainless steel pipe users do not have to question this point.Which one is better,Model & mdash; Except that the risk of weld corrosion of the material is reduced due to the addition of titanium, other properties are similar. Stainless steel decorative pipe, stainless steel pipe, series stainless steel pipe & mdash; Ferritic and martensitic stainless steel model & mdash; Good heat resistance, weak corrosion resistance,Patarra304L stainless steel square tube, % Cr % Ni.Stop the written technical disclosure, on-site technical and safety disclosure to the on-site operators.Crimping: during crimping the convex part of the pipe fitting is placed in the concave groove of the die, and the jaw is perpendicular to the pipe axis.
Hardness stainless steel pipes are usually measured by Brinell,Patarra304 stainless steel welded pipe, Rockwell and Vickers hardness indexes.supply,The specific steps of continuous casting billet process of stainless steel pipe fittings are as follows: according to different steel grades, the vibration process of mold is matched with protective slag, which can improve the yield of %, save energy and shorten the production cycle, so as to improve the yield of molten steel.Today, Xiaobian can help you. If you want to choose high-quality stainless steel pipe water supply pipe, you can choose this: choose the material of stainless steel pipe water supply pipe.Low temperature embrittlement of stainless steel pipe --- in low temperature environment, the deformation energy is small. In low temperature environment, the phenomenon of reduced elongation and area shrinkage is called low temperature embrittlement. It is mostly produced on the body centered cubic structure of ferrite series.Patarra,Stop the written technical disclosure, on-site technical and safety disclosure to the on-site operators.That is stainless steel. The GB brand is CrNi. & mdash; it has better temperature resistance than it.The petrochemical industry, including the chemical fertilizer industry, has a great demand for stainless steel pipes. Stainless steel pipes are mainly used in this industry, including, , l, etc., with an outer diameter of about ￠ - ￠ and a wall thickness of about mm-mm (generally medium and low pressure transmission pipes with a specification of more than & phi; mm). The specific application fields are: furnace pipes, material transmission pipes, heat exchanger pipes, etc.